|
Back to Blog
The Best Tips for Handling Flat Tires7/26/2019 Today, we all have cell phones. We completely rely on our phone to save us in any sort of emergency. But, there are always chances when you may forget your phone at home, or forget to charge it or be unreachable, or out of range; anything may happen. In the shape of flat tires, your cell phone may sometimes not be the right substitute. Fortunately, tire change is not rocket science. A stepwise guide can help you stay prepared for the flat tire change. As said and believed, spare tires are the temporary set of tires with which you should not drive for long distances as well as should not ride at high speeds. If not having the right knowledge, it is a good idea to search out the best 'flat tire repair service near me' and get your tires checked. The trained technicians at any local tire repair service will be able to guide you if your flat tire needs to be replaced or can be repaired.
In case if you get stuck in the middle of your journey where it could be hard to reach out to a technician, you can change your car tires on your own by following the right guide. Step #1: Turn on hazard warning lights Immediately after you realize that you are having a flat tire switch on the hazard warning lights. Doing this you are letting other drivers around you know that there is something wrong. Step #2: Drive your car to a safe side of the road After turning on the hazard lights pull your car over the safe stretch of road, put on the parking breaks, and turn off your car. Never stop it over a narrow edge. Make sure that you are securely getting the safe distance down the road. Step #3: Find out wheel wedges Wheel wedges are used to prevent accidental car movements. If you don't have them find out bricks, some wood pieces, or stone of suitable size. Whatsoever you get, put it behind the tires so it doesn't move. Place the wedges behind the front tires if the rear tire is flat and put them behind the rear tires if the front one is flat. Step #4: Take wheel hubcap away Tires in most vehicles usually are covered with hubcap protecting the lug nuts. Hubcap is easy to remove. Do it before you jack up the car to change a flat tire. The lug wrench having flat edge usually slips between the tire and hubcap when setting it off Step #5: Make the lug nuts less tight Turn the lug nuts anticlockwise with the help of lug wrench. Lug nuts are always over tightened. So you may need to use your highest level of force to break the resistance of nuts. Putting your body weight or your foot on the lug wrench can help you loosen the nuts. Don't take them off until you are ready to remove the flat tire. Step #6: Place the jack close to the flat tire Maneuver a jack under your car's frame next to the tire that is to be replaced. Your vehicle may have a cleared spot of metal and also a molded plastic spot. They are specifically designed for jack to prevent accidental damages that may appear while lifting the vehicle. Step #7: Lift your vehicle up If required place an ample piece of wood under the jack before pulling the vehicle up. This will ideally help you prevent your vehicle from getting off the jack when it is settling into the weight of your car. Slowly lift your car to get the flat tire approx six inches above the road surface. Step #8: Detach the lug nuts from the tire Take all the lug nuts off the tire. Since they are already been loosen you should be able to remove them by your hand. Take them out completely and keep safely aside. Do not lose any of them. Step #9: Gently remove the tire Gently hold the tire treads and pull it out of the hub. Keep it aside in a way it does not roll onto the road. Step #10: Set up the replacement tire Line the replacement tire up with the lug bolts and rim. Push the spare tire onto the rim gently until you can see the lug bolts through the rim. Step #11: Over tighten the lug nuts Fix all the lug nuts back into the bolts and tighten them as much as you can. Once you get them all on, double-check if none of them are still loose. If required tighten them again. Step #12: Bring the car down. Lower down your car and remove the jack. Take the lug wrench and tighten all the nuts by turning them clockwise. Step #13: Put the hubcap back on the tire and it's done Put the hubcap back on the tire if it fits with the spare one; otherwise, simply store it with the flat tire. Arrange everything back into your car before leaving. Most preferably, meet to a reputable technician as early as possible and get your flat tire checked if it can be repaired or not. With the above treated simple tire changing tips there are a few more things to follow to maintain the tip-top shape of your tires for long.
Moreover, when having your flat tire change in Mississauga, the experts will recommend you to split all four tires at once. Moreover, if you only want to purchase two new tires, make sure that two new tires are installed on the back. You may need them for the remaining tires that you haven't replaced. If you are looking for getting your car tires inspected, Quick Tire Repair is the best place to visit. Have a word with expert technicians about the best brand of tires that can be the best fit for your vehicle. Before making your final choice between winter tires, summer tires, or all-season tires, it is advisable to double-check the car's manual.
1 Comment
Read More
truckexpert
4/11/2023 11:22:54 am
Great Post! Inorder to find truck repair service near your location visit <a href="https://www.breakdowninc.com/">Breakdown Inc</a> and find the nearest repair shop to your location.
Reply
Leave a Reply. |